Discontinued Vintage Appliance Parts, Recreated to Order
Can't find a part for your vintage refrigerator, stove, oven, washer, dryer, mixer, radio, fan, or other appliance? Cordane Print Co, a veteran-owned 3D printing shop in McAllen, Texas, recreates discontinued and hard-to-find parts from a sample of the original (even a broken one) or from measurements. Each part is made to fit your make and model, and we match the color as close as we can to the original factory color. Nothing is made until you approve the quote.
Parts We Make for Vintage Appliances
For appliance repair shops, restorers, resellers, and owners.
Handle pieces & end caps
Handle pieces and end caps for older ranges, ovens, washers, dryers, and refrigerators.
Control & thermostat knobs
Control knobs for stoves, ranges, washers, dryers, mixers, radios, and fans.
Clips & supports
Light-duty clips, rack and shelf supports, and retainers.
Trim, bezels & covers
Trim, bezels, covers, and latch and hinge covers, without logos.
Recent Vintage Parts
Proof of vintage-part work: recent replacement parts we've made.
What We Won't Make (and Why)
Honest scope up front.
Good candidates
- Knobs, handles, and caps
- Clips, retainers, and trim
- Covers, housings, and bezels
- Light-duty brackets, mounts, and spacers
What we'll turn down
- Load-bearing parts
- High-heat parts near heating elements, burners, exhaust, or the engine block
- Safety-critical parts: fuel, gas, steering, brakes, motor mounts
- Parts carrying a manufacturer's logo or trademark
Will a 3D Printed Part Hold Up?
For clips, knobs, trim, and covers, yes. We recommend the material for each job: PETG, ASA, Nylon-CF, or TPU. For heavier shelf or drawer loads, we'll tell you if printing isn't suited. We don't make parts meant for food contact. Materials guide →
How It Works for Repair Shops and Restorers
You see the price before anything is made.
Send the part or photos
Send photos and measurements through the quote form, with the make, model, and year. Or mail the original, even if it's broken. Email us first for the address.
Get a quote
Price, timeline, and material by email.
Approve it
Nothing is made until you approve. For critical fits, we can make a first piece for you to check.
We make, check, and ship
We check the part against the original or your measurements, then ship it.
Reorder anytime
We keep your file on hand, so reorders skip the design step.
More on how it works and all repair parts.
For Shops: One Piece or a Batch
Restorers and repair shops that need the same part again can order a batch. Reorders and batches cost less per piece, and your file stays on hand.
Common Questions
Can you recreate a discontinued part for my vintage refrigerator or other appliance?
Often, yes. If a part is no longer made or is hard to find, we can recreate it from a sample or from measurements, made to fit your appliance and color matched as close as we can to the original factory color. This works for refrigerators, stoves, washers, dryers, mixers, radios, fans, and other appliances, as long as the part isn't load-bearing, high-heat, or safety-critical.
Can a discontinued appliance part be 3D printed?
Often, if it isn't load-bearing, high-heat or safety-critical.
My handle or knob is broken. Can you still copy it?
Yes. Send the broken part or clear photos with measurements.
Will a 3D printed appliance part be strong enough?
Light-duty clips and supports, yes, in the right material. For heavy loads, we'll tell you if printing isn't suited.
Are your parts food safe?
We don't make parts meant for food contact. We make handles, knobs, trim, clips and covers.
Can you make stove or oven knobs?
Control knobs, yes, like our D-shaft knob example. We don't make anything that sits near burners or heating elements.
What information do you need for a quote?
The make, model and year, photos, and measurements, or the original part.
Do I have to mail you the original part?
No. Photos and measurements often work. Mail it if you can, and email us first for the address.
Can you match the original color?
We aim to match the color as close as possible to what the part was when it was originally made. It's a best effort, not a guarantee, and we'll tell you if we can't get close.
Can you add the original brand logo?
No. We don't reproduce manufacturer logos or trademarks.
How much does a replacement part cost and how long does it take?
Price and timeline come with the quote, and nothing is made until you approve.
Do you ship nationwide?
Yes, we ship nationwide. Local pickup in McAllen for Rio Grande Valley customers.
Send Us Your Part
Send a photo and measurements, or the part itself. You'll get a price and timeline before anything is made.
We ship nationwide. Local pickup in McAllen for Rio Grande Valley customers.
Prefer to talk? Call (216) 202-2693